數控焊接設備與其他焊接設備相比要注意
來源:http://m.xihagames.com/ 發布時間:2022-06-16 瀏覽次數:0
數控焊接設備與其他焊接設備相比,該自動焊接設備具有更高的自動化程度,其所有部件均選自高質量的原始設備,并且操作非常簡單方便。自動焊接機工作速度較快,深度較大,不易變形。可以同時進行多束加工和多工位加工,使焊件更加準確。但是,全自動焊接機的安裝不是那么簡單。在安裝之前,要有一個良好的安裝環境,并且要執行相應的保護。
Compared with other welding equipment, this automatic welding equipment has a higher degree of automation. All its components are selected from high-quality original equipment, and the operation is very simple and convenient. The automatic welding machine has fast working speed, large depth and is not easy to deform. It can carry out multi beam processing and multi station processing at the same time, making the weldment more accurate. However, the installation of automatic welding machine is not so simple. Before installation, there should be a good installation environment and corresponding security protection should be implemented.
使用山東數控焊接設備的注意事項:
Precautions for using Shandong CNC welding equipment:
1.焊槍電纜不要壓得太緊,彎曲角度也不能太小。送絲軟管的半徑不應小于150mm,否則內部電纜會損壞,可能導致事故。焊接期間請勿更改電壓調試開關。
1. the welding gun cable shall not be pressed too tightly and the bending angle shall not be too small. The radius of the wire feeding hose shall not be less than 150mm, otherwise the internal cable will be damaged, which may cause accidents. Do not change the voltage adjustment switch during welding.
2.在焊接操作過程中,請勿觸摸帶電部件,例如焊接機的輸出接口。
2. during the welding operation, do not touch the live parts, such as the output interface of the welding machine.
3.更改或調試面板旋鈕時,請勿過分用力。自動不銹鋼管焊接機可能會損壞設備。
3. do not use excessive force when changing or debugging the panel knob. Automatic stainless steel pipe welding machine may damage the equipment.
4.每次焊接之前,請檢查焊接機的連接是否正確以及接地線是否可靠。
4. before each welding, please check whether the welding machine is connected correctly and whether the grounding wire is reliable.
數控焊接設備檢查:操作員在每次焊接操作前要檢查以下項目:
Safety inspection of NC welding equipment: the operator shall check the following items before each welding operation:
1.確保焊接機相互良好的接地是可靠的安裝。
1. ensure that the welding machine is reliably grounded.
2.確保焊接機的輸入和輸出電纜完好無損。
2. ensure that the input and output cables of the welding machine are intact.
3.安裝并固定了焊接機后,人員要定期對其進行檢查。
3. after the welding machine is installed and fixed, professionals should regularly inspect it.
使用山東數控焊接設備時,必須可靠地對其進行定位和夾緊,這可以防止和減少焊接變形并將工件放置在理想的焊接位置,這對于確保焊縫的完整性是很有用的。良好地形成焊接并提高了焊接速度。
When using Shandong numerical control welding equipment, it must be reliably positioned and clamped, which can prevent and reduce welding deformation and place the workpiece in the ideal welding position, which is very useful to ensure the integrity of the weld. The welding is well formed and the welding speed is improved.
對于焊接機械手,應盡可能使用通用和標準化的焊接支撐設備,這有助于充分發揮機械手的效率;當然,所選擇的焊接機械手具有更好的制造技術和更高的機械效果,否則將無法正常使用。
For the welding manipulator, general and standardized welding support equipment shall be used as far as possible, which will help to give full play to the efficiency of the manipulator; Of course, the selected welding manipulator has better manufacturing technology and higher mechanical effect, otherwise it will not work normally.
當使用焊接機械手時,對支撐設備的選擇,特別是設備的剛性以及設備的形式和尺寸精度有更高的要求。焊接開始時,熱傳導,導電率,磁絕緣和絕緣對焊接設備有特定要求。
When a welding manipulator is used, there are higher requirements for the selection of supporting equipment, especially for the rigidity of the equipment and the form and dimensional accuracy of the equipment. At the beginning of welding, heat conduction, conductivity, magnetic insulation and insulation have specific requirements for welding equipment.
不會有內部間隙等異常情況。檢查并確認送絲輥的凹槽和齒型完好無損,并且在磨損或接觸不良時應更換輥和接觸頭塊。
There will be no abnormal conditions such as internal clearance. Check and confirm that the groove and tooth profile of the wire feeding roller are intact, and replace the roller and contact head block in case of wear or poor contact.
以上就是今天為大家分享的關于問題的相關內容,希望對大家能有所幫助,想要了解更多內容可以電話聯系我們或者關注我們的網站http://m.xihagames.com。
The above is the relevant content about the problem shared for you today. I hope it can help you. If you want to know more, you can contact us by phone or follow our website http://m.xihagames.com 。
上一篇:數控切割機的工作流程
下一篇:焊接專機從分類使用事項了解起來